收藏本站
Signals/Connections
Table 2-10. Host Interface (Continued)
Signal Name
HA0
Type
Input
State During
Reset 1, 2
Ignored Input
Signal Description
Host Address Input 0— When the HI08 is programmed to interface with a
non-multiplexed host bus and the HI function is selected, this signal is line 0
of the Host Address bus.
HAS/HAS
PB8
Input
Input or
Output
Host Address Strobe— When the HI08 is programmed to interface with a
multiplexed host bus and the HI function is selected, this signal is the Host
Address Strobe (HAS) Schmitt-trigger input. The polarity of the address
strobe is programmable, but is configured active-low (HAS) following reset.
Port B 8— When the HI08 is configured as GPIO through the HPCR, this
signal is individually programmed through the HDDR.
HA1
Input
Ignored Input
Host Address Input 1— When the HI08 is programmed to interface with a
non-multiplexed host bus and the HI function is selected, this signal is line 1
of the Host Address bus.
HA8
PB9
Input
Input or
Output
Host Address 8— When the HI08 is programmed to interface with a
multiplexed host bus and the HI function is selected, this signal is line 8 of the
Host Address bus.
Port B 9— When the HI08 is configured as GPIO through the HPCR, this
signal is individually programmed through the HDDR.
HA2
Input
Ignored Input
Host Address Input 2— When the HI08 is programmed to interface with a
non-multiplexed host bus and the HI function is selected, this signal is line 2
of the Host Address bus.
HA9
PB10
Input
Input or
Output
Host Address 9— When the HI08 is programmed to interface with a
multiplexed host bus and the HI function is selected, this signal is line 9 of the
Host Address bus.
Port B 10— When the HI08 is configured as GPIO through the HPCR, this
signal is individually programmed through the HDDR.
HRW
Input
Ignored Input
Host Read/Write— When the HI08 is programmed to interface with a
single-data-strobe host bus and the HI function is selected, this signal is the
Host Read/Write input.
HRD/HRD
PB11
Input
Input or
Host Read Data— When the HI08 is programmed to interface with a
double-data-strobe host bus and the HI function is selected, this signal is the
Host Read Data strobe (HRD) Schmitt-trigger input. The polarity of the data
strobe is programmable, but is configured as active-low (HRD) after reset.
Port B 11— When the HI08 is configured as GPIO through the HPCR, this
signal is individually programmed through the HDDR.
Output
DSP56311 User’s Manual, Rev. 2
2-10
Freescale Semiconductor
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
DSPAUDIOEVMMB1E BOARD MOTHER DSP563XX
DSPIC30F2010 DEVELOPMENT KIT KIT DEV EMBEDDED C
DSTRM-KT-0181A DSTREAM DEBUG AND TRACE UNIT
DSUT1CSU SURGE SUPPR NETWORK W/GROUND
DTEL2 SURGE SUPPRESSOR PHONE RJ11/RJ45
DV003001 PROGRAMMER PICSTART PLUS 16C/17C
DV164035 MPLAB ICD3 IN-CIRC DEBUGGER
DV164039 KIT DEV PIC24FJ256DA210
相关代理商/技术参数
DSP56311EVMIG_D 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311EVMIG DSP56311EVM Sample Code
DSP56311EVMUM 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 Evaluation Module Hardware Reference Manual
DSP56311FACT 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 Higher performance programmable DSP for demanding voice and data applications
DSP56311UM 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 24-Bit Digital Signal Processor Users Manual
DSP56311UMAD 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 Users Manual Addendum
DSP56311VF150 功能描述:数字信号处理器和控制器 - DSP, DSC 150Mhz/300MMACS 150Mhz EFCOP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSP56311VF150B1 功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSP56311VF150R2 功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT